Top Tips Of Renovate NS0-520 Testing Bible

NEW QUESTION 1

You want to connect a NetApp AFF A700 to a 32 Gb FC switch. The ports need to connect at 32 Gb speed. In this scenario, which statement is correct?

• A. The AFF A700 includes FC ports natively on the controller.
• B. The AFF A700 includes an additional FC I/O module that is already populated in each controller.
• C. You need to purchase a two-port or four-port unified I/O module that enables FC and Ethernet connectivity.
• D. You need to purchase a two-port or four-port FC I/O module.

Answer: C

NEW QUESTION 2

You have deployed an AFF 400 systems for ISCSI workloads and want to ensure maximum performance to the hosts.
In this scenario, which two steps should be configured? (Choose two)

• A. Enable Jumbo frames on the network switch
• B. Enable Jumbo frames on the LIF
• C. Enable Jumbo frames on the broadcast domain
• D. Enable Jumbo frames on the IPspace

Answer: AC

Explanation:
Changing the Network port settings at the broadcast domain level will change all ports in that broadcast domain sequentially, or one at the time. This will only cause a disruption if the port is a single point of
failure.
Enable jumbo frames (typically MTU of 9000).All devices in the data path, including initiators, targets, and switches, must support jumbo frames. Otherwise, enabling jumbo frames actually reduces network
performance substantially.
You can find more information on this link: https://kb.netapp.com/Advice_and_Troubleshooting/Data_Storage_Software/ONTAP_OS/How_to_enable_jum

NEW QUESTION 3

You want configure namespaces to support NVMe over Fibre Channel (NVMe/FC) using ONTAP 9.8. Which action will accomplish this task?

• A. Add FC to the list of SVM protocols
• B. Remove any protocols from the SVM before adding the NVMe protocol
• C. Enable ALUA on the namespaces that should use the NVMe protocol
• D. Configure a LIF for the NVMe protocol

Answer: D

Explanation:
Although ONTAP uses a NVMe/FC LIF that is separate from the FCP LIFs, both LIFs can be hosted on the same physical HBA port at both the host initiator and storage target. NVMe/FC and FCP can
share the same physical infrastructure concurrently, so the same physical port, cable, switch port, and target port can simultaneously host and transmit both FCP and NVMe/FC frames
NVMe can use the same FC infraestructure, but it needs to create a separate NVMe LIF to work. You can find more information on this link:
https://www.netapp.com/de/media/10681-tr4684.pdf (14)

NEW QUESTION 4

While changing the network connections on your ONTAP cluster from twinax to fiber, the ports experience network connectivity issues. You want to verify which speeds the ports support and ensure that you
have supported transceivers. In this scenario which two actions would accomplish this task (choose two)

• A. Use hardware universe to determine the supported transceivers
• B. Use the interoperability matrix tool to determine the supported port speeds
• C. Use hardware universe to determine the supported port speeds
• D. Use the interoperability matrix tool to determine the supported transceivers

Answer: AC

Explanation:
Hardware universe will show information about port speeds and transceiver compatbility You can find more information on this link: https://hwu.netapp.com/Resources/hwu_ug.pdf (page 73)

NEW QUESTION 5

Which two are supported in ONTAP 9.5? (Choose two.)

• A. an NVMe LIF and an FC LIF in the same SVM
• B. an NVMe LIF associated with an FC Direct Connect port
• C. a NVMe LIF and an FC LIF associated with the same port
• D. multiple NVMe LIFs in the same SVM

Answer: CD

NEW QUESTION 6

You are setting up FC ports and must configure the speeds for both the SAN and the host ports. In this scenario, which statement is correct?

• A. Set the target port speed higher than the switch port speed.
• B. Set the target port speed to auto-negotiation.
• C. Set the target port speed to match the switch port speed.
• D. Set the target port speed lower than the switch port speed.

Answer: B

NEW QUESTION 7

Which topology allows for guaranteed maximum network performance for iSCSI?

• A. isolated VLAN network
• B. MetroWAN network
• C. direct connect
• D. WAN network

Answer: C

NEW QUESTION 8


A customer has an AFF A700 connected to a Cisco switch and has verified connectivity but cannot see any LUNs. The customer issued the run -node scaling-01 -command fcp topology show command to verify the connection.
Referring to the exhibit, what needs to be enabled on the Cisco switch?

• A. Trunking needs to be enabled.
• B. VSAN needs to be enabled.
• C. NPIV needs to be enabled.
• D. VFC needs to be enabled.

Answer: D

NEW QUESTION 9

After performing failover testing on a newly deployed MetroCluster configuration, some aggregates remain in a degraded state. Referring to the exhibit, which statement is true?

• A. The MetroCluster Tiebreaker software is misconfigured
• B. The ONTAP Mediator service is misconfigured
• C. A cluster switch is powered off
• D. A disk shelf is powered off

Answer: D

Explanation:
The aggregate with drives on the powered-off shelf should have a degraded RAID status, and drives on the affected plex should have a failed status
You can find more information on this link:
https://docs.netapp.com/us-en/ontap-metrocluster/install-ip/task_test_the_mcc_configuration.html#verifying-ope

NEW QUESTION 10

What are two benefits of implementing VLANs for ISCSI configuration? (choose two)

• A. Reduced number of broadcast domains
• B. Increased performance
• C. Increased security
• D. Increased resiliency

Answer: AC

Explanation:
When you implement VLANs in large IP network infrastructures, you derive the following benefits: Increased security.
VLANs enable you to leverage existing infrastructure while still providing enhanced security because they limit access between different nodes of an Ethernet network or an IP SAN.
You can find more information on this link:
https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-sanconf%2FGUID-C5288E55-DA

NEW QUESTION 11

Which NetApp tool views automated, schedule configuration, and performance data for a customer's SAN from a Web browser?

• A. Virtual Storage Console
• B. OnCommand Workflow Analyzer
• C. Config Advisor
• D. Active 1Q

Answer: B

NEW QUESTION 12

Which tool collects configuration data from hosts and switches to assist in evaluating a qualified configuration?

• A. System Manager
• B. syssta
• C. command
• D. SnapCenter
• E. OneCollect

Answer: D

NEW QUESTION 13

You have a 4-node FAS8200 A300 cluster that are using ONTAP 9.3 default settings. For faster performance, you move a volume with LUNs from a node on the FAS8200 to a node on the AFF A300. You determine that your SAN host is still using all active/optimized FC paths to the FAS8300 HA pair.
What do you need to troubleshoot to move all active/optimized FC paths to the AFF A300 HA pair?

• A. reporting nodes list
• B. host MPIO and ALUA
• C. LUN mapping
• D. igroup WWPNs

Answer: A

NEW QUESTION 14

You recently bought a FAS8200 series with SAS drives and want to maximize data efficiencies. Performance is not a primary Which two statements are correct in this scenario? (Choose two.)

• A. Enable both inline and post process efficiencies.
• B. Enable always-on compaction.
• C. Enable always-on deduplication.
• D. Enable compression.

Answer: AC

NEW QUESTION 15

An SVM's LUN setup needs to have LIFs that are configured for FC access and iSCSI access. The administrator will also be using NetApp Virtual Storage Console.
In this scenario, which three types of LIFs are required? (Choose three.) FC LIFs

• A. management LIFs
• B. iSCSI data LIFs
• C. NAS data LIFs
• D. intercluster LIFs

Answer: ABC

NEW QUESTION 16

You want to perform online data migration using Foreign LUN Import. In this scenario, which two conditions are required to support this task? (choose two)

• A. ISCSI protocol LIFs must be added to the data SVM
• B. ISCSI targets must be added to the ONTAP ISCSI initiator
• C. FCP protocol LIFs must be added to the data SVM
• D. FCP initiator ports must be available

Answer: CD

Explanation:
FLI does not support iSCSI connections directly. In order for iSCSI LUNs to be migrated using FLI, the LUN type must be changed to FC. After the migration is complete, the LUN type is changed back to
iSCSI.
You can find more information on this link:
https://docs.netapp.com/us-en/ontap-fli/san-migration/concept_lun_requirements_and_limitations.html

NEW QUESTION 17
......