Cisco 300-180 Exam Dumps 2021

NEW QUESTION 1
A customer is deploying multihop FCoE in its network. Which guideline must the customer follow with respect to VE ports to make this deployment possible?

• A. Auto mode on the vFC interface is supported.
• B. VE-port trunking is supported over FCoE-enabled VLANs.
• C. VE-port interface binding to MAC addresses is supported.
• D. A VE port is disabled for trunk mode by default.

Answer: B

NEW QUESTION 2
Which command displays the traffic statistics for a port channel interface?

• A. show interface port-channel channel-number
• B. show port-channel traffic
• C. show port-channel usage
• D. show port-channel compatibility-parameters

Answer: B

NEW QUESTION 3
Which command do you to identify whether the ACI fabric discovered and the TEP addresses are assigned?

• A. Show lldp neighbors
• B. acidiag fnvread
• C. Show lldp neighbors node
• D. acidiag fnvread

Answer: B

NEW QUESTION 4
Refer to the exhibit.

The firmware fails while using AutoInstall. What cloud cause this issue?

• A. A maximum of two active partitions is permitted when using AutoInstall
• B. The bootflash partition exceeded 70 percent of the capacity of the flash drive.
• C. The license for the Advance Services package must be installed.
• D. The workspace partition must be at least 10 percent of the flash drive.

Answer: B

NEW QUESTION 5
A customer reports that they are missing vPC peer link redundancy between two Cisco Nexus 5548UP switches. The interfaces on both switches are configured and cabled correctly. The interface status is up/down on switch 1 and up/up on switch 2, Which two steps should be taken to isolate the root cause? (Choose two.)

• A. Swap the ends of the fiber-optic cable
• B. ask the customer if the link was ever functional
• C. determine whether the fiber-optic cable manufacturer is valid under the interoperability matrix
• D. swap the transceivers between the two interfaces
• E. determine Whether the fiber-optic cable type (single mode or multimode) matches the X2 modules

Answer: AD

NEW QUESTION 6
Refer to the exhibit.

What command should you execute next in resolving a lock failure?

• A. ntp execute
• B. ntp commit
• C. ntp lock
• D. ntp help
• E. ntp detail

Answer: B

NEW QUESTION 7
Which statement about the Nexus atomic rollback feature is true?

• A. it restores the default manufacturing configuration.
• B. Each error must be acknowledged prior to implementation.
• C. it is implemented only if error occur.
• D. it is implemented and any errors are skipped.

Answer: C

NEW QUESTION 8
Which statement is true regarding how OTV edge devices will react based on the configuration of the VLANs being extended across the overlay network?

• A. Any VLANs not extended will not be populated in the local OTV route table.
• B. Only the same-site edge AED device controls which VLANs are to be extended.
• C. Any extended VLANs will not be populated in the remote OTV route table.
• D. By default, all VLANs on an edge device will be extended.

Answer: A

NEW QUESTION 9
You are no longer seeing updates to the device-aliases database on your Cisco Nexus 5596UP Switch. Which command is useful to determine if the scope of Cisco Fabric Services application distribution was being administratively limited?

• A. N5K2# show cfs region
• B. N5K2# show cfs scope
• C. N5K2# show cfs locale
• D. N5K2# show cfs acl
• E. N5K2# show cfs firewall

Answer: A

NEW QUESTION 10
You are troubleshooting a Cisco Nexus 1000V Series Switch. Which command can you use to re-establish communication between VSM and VMware vCenter?

• A. reset
• B. connect
• C. setup
• D. reload

Answer: B

NEW QUESTION 11
A customer is trying to boot an operating system that is installed on the eUSB on a Cisco UCS B-Series blade server; however, the boot fails. What is the cause of this failure?

• A. The local disk must be the first device in the boot order.
• B. eUSB is not a supported boot device.
• C. eUSB support is available only on the Cisco UCS C-Series rack server.
• D. eUSB is not the first device in the boot order for the server.

Answer: D

NEW QUESTION 12
Refer to the exhibit.

The output displays a failed SFP validation. What is the cause of the failure?

• A. The fiber is not connected to the SFP
• B. The SFP is not a valid Cisco SFP
• C. The speed needs to be changed to 10000,
• D. The speed needs to be changed to 1000

Answer: A

NEW QUESTION 13
You are troubleshooting LACP issues on a Cisco Nexus platform. Which two LACP modes can you view by using the show lacp interface command? (Choose two.)

• A. passive
• B. active
• C. standby
• D. auto-negotiate
• E. on

Answer: AB

NEW QUESTION 14
You have upgraded your Cisco Nexus 7009 Switches and converted the default VDC to an admin VDC. You notice that all of the ACLs are still present on the admin VDC after the conversion. What should you do?

• A. enable configuration synchronization between the admin VDC and the production VDCs
• B. delete the ACLs
• C. delete all ACLs except those related to CoPP
• D. delete all ACLs except those bound to resource templates
• E. use the system admin-vdc acl command to properly migrate ACLs

Answer: B

NEW QUESTION 15
An administrator disassociates the service profile from a server. What happens to the identity and connectivity information for the physical server?

• A. it takes parameters of other servers in the service profile.
• B. it is reset to factory details.
• C. it uses master service profile parameters.
• D. it is maintain and can be reused.

Answer: D

NEW QUESTION 16
ACisco Nexus 7010 Switch that is at the core of a customer network has high CPU utilization. What can the customer do to prevent a network outage and identify why CPU utilization is high?

• A. apply a rate limit on the interfaces with high traffic
• B. use CoPP
• C. use HSRP and vPC for redundancy to handle high CPU utilization
• D. use the show process cpu command to see the high CPU utilization

Answer: B

NEW QUESTION 17
Refer to the exhibit. You fail to configure a boot from iSCSI service profile. Which action do you take to troubleshoot the issue?

• A. Attempt to ping the IP address of the iSCSI target.
• B. Check the LUN masking configuration.
• C. In the CLI of Cisco UCS Manager, verify that the blade is attached to the LUN.
• D. Check the native VLAN configuration on the overlay vNIC.

Answer: D

NEW QUESTION 18
Refer to the exhibit. Anycast RP fails. Which two actions do you perform to resolve the issue? (Choose two.)

• A. Configure the IP address of Anycast RP to use the multicast range.
• B. Change the loopback2 interface on Nexus 2 to 10.1.1.1/32.
• C. Change the pim rp-address on Nexus 2 to 10.1.1.1.
• D. Add the pim ssm range to Nexus 1.
• E. Set the pim ssm range on Nexus 2 to 225.0.0.0/24

Answer: BC